San Diego Water Heater Safety Precautions

Posted by on Dec 4, 2013 in Plumbing Repair San Diego, Water Heater Repair San Diego

Correctly maintaining ones water heater is essential not simply so it works to its complete capacity and can save some energy money, however for safety concerns too. Yes, it can blow up – it doesn’t occur too commonly for homeowners, however undoubtedly this is something that Water Heater Repair San Diego does not wish to have take place to you!

Venting can be kind of technical however we will review the essentials here. The vent need to be the same diameter as the draft diverter of the water heater tank. It is expected to go up and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent need to go out a side wall. As for power-vent heaters, the fan blows the fumes out, so there is some versatility in the instructions they are vented.

Any roofing or wall that the vent goes through need to be a double wall. The single wall pass throughs ought to be screwed with three screws per section. If these fundamentals are not stuck to, the vents can break down in time and carbon monoxide gas can cause significant troubles within ones house. Naturally we do not desire that to take place!

The only other concern with ventilation is that of backdrafting. The fumes can consume the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a great circumstance for a correctly working water heater. If the fumes go back inside the instead of being correctly vented outside, the fumes can get in the living locations of the home. Soot issues can develop also.

Dielectric Connectors
The steel water heater is linked to cooper pipes by the dielectric connectors. When two these 2 metals are assembled in water electrolysis takes place. The process rusts one metal away to secure the other. This process is important in securing the inside of the water heater. Inspection for leaks must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a crucial part of the water heater, for it helps make sure the darn thing does not blow up under pressure if the temperature surpasses the proper limits the water heater is developed for. Once a year (at least) the T&P valve need to be examined to ensure, it is working correctly, for they can be prone to failure. Merely lifting up on the handle water should stream easily out and stop when the handle is let go of. If it simply runs or drips, or does absolutely nothing at all, it will need to be changed.

The drain lines for the T&P line ought to not be routed up, because water does not stream uphill too well. Make certain it goes down and or out please. If water is running out the drain line regularly, it is the indicator of something incorrect too. It might be one of a number of various things that we will not go into below – simply get in touch with a local plumber please.

Earthquake Straps
Yep, even if you don’t stay in an earthquake zone and are needed to have these on ones water heater, it is a pretty good idea to do so. It looks like the majority of all new homes in sub-divisions these days have the water heater in the garage. Yes, there is normally a concrete curb in front of it so one does not drive a vehicle into it, but things can inadvertently knock it over so be safe and strap that thank in.

Temperature Setting
It appears most domestic water heater tanks have setups of warm – hot – extremely hot … and not degree settings. Some “tips” on conserving energy at home specifically in the winter season time, say to decrease the setting on the tank to 120 degrees. That’s fantastic for saving energy but legionella microorganisms, which triggers Legionnaire’s condition can grow at 120 degrees. By breathing in the mist from the water in the shower, one can inhale the microorganisms. Look for a medium in between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature so beware.

Anode Rods
These generally are made of aluminum and there is absolutely nothing wrong with that in concept, though we recommend using magnesium ones. Let’s state for whatever reason there is some kind of emergency or catastrophe where one lives and one needed to utilize the water in the water heater for drinking water (since bunches of emergency readiness individuals encourage doing so). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be packed with aluminum compounds, which is not good for the body. It is bad for the stomach, intestines and joints.

The anodes help with rust defense and are vital in extending the life of the water heater. They can likewise assist with odor issues with the water. Overall, magnesium anodes just work much better for a great deal of different reasons like the health advantages, let develop of sediment, a quieter water heater, and they often work better with softened water.

Drain Valve
Ok, simply inspect it at least yearly to make certain the darn thing opens and works. And it is great to drain and purge the tank at least once a year anyhow (something you obviously are doing currently). If for some reason one should use the water during a disaster or drain it to rather a loud tank and have actually not drained it frequently, and it does not open, it will take longer to fix the trouble you are initially attempting to repair.

Combustion Changer Hatch
Since gas and oil water heaters breathe the air sucked in from underneath, combust with it and exhale it, it is essential to keep the area around it, specifically beneath the water heater, clean and swept. If if is not burning appropriately, it can cause composing issues (pointed out above), in addition to combustion and fume troubles and possibly be a fire threat. A few of analyzing the chamber and how the flame burns is objective so we are not going to enter a lot of information right here. it is very important to see if the combustion chamber roof has a bunch of rust or water markings or is black in color. These are not an excellent indicator at all. One ought to see some blue flame at the bottom when it burns and orange and yellow at the top, however, the yellow need to not be incredibly high up. One ought to see grey metal, some white condensation marks are okay.

We have put together an infographic to highlight the information above:

 Water Heater Repair San Diego

Phil Luther Plumbing Content Writer and Curator Phil is a prolific writer of content for plumbing related websites in the United States. Google Profile